產品列表 / products
- 美國 METCAL OKI
- 美國 PACE 佩斯
- 德國 ERSA 埃莎
- 日本 HAKKO 白光
- 美國 LICOTA（力可達）
- 美國 Techcon泰康
- 美國 ITW Chemtronics
- 德國 WELLER 威樂
- 英國 Torqueleader 工具
- 德國 GEDORE 吉多瑞
- 美國 STANLEY 史丹利
- 美國GORDON刷子
- 日本 Mitutoyo 三豐
- 德國 STEINEL 司登利
- 英國 BOWERS 寶禾
- 中國臺灣 Pro'sKit （寶工）
- 焊臺/吸煙儀/烙
- 電動螺絲刀/扭
- 扭力工具/手動
- 瑞士 TESA 量具
- DAB
- 美國TREK
- 瑞士PB SWISS TOOLS
- American Beauty 工業焊臺
- 日本TRUSCO
- 諾信
ITW Chemtronics CW2200STP CW2200MTP 導電筆檢測報告
美國 ITW Chemtronics 導電筆
CW2200STP 標準頭 直徑1.2mm 8.5g 0.32 oz
CW2200MTP 微型頭 直徑0.8mm 8.5g 0.32 oz
能地劃出高導電性地銀線路，跳線：
·快速創建導電的銀線路
·操作簡單
·可在低溫下焊接
·室溫下幾分鐘可干
·可選擇微型筆頭（用于細線）或標準筆頭（較粗的線）
應用：
·修補線路
·連接元件
·制作光滑的跨接線
·屏蔽電子裝置
TDS # CW2200
PRODUCT DESCRIPTION
CircuitWorks® Conductive Pen makes instant highly conductive silver traces on circuit boards. CW2200 is used in prototype, rework, and repair of circuit boards by linking components, repairing defective traces, and making smooth jumpers. The silver traces dry in minutes and have excellent adhesion to most electronic materials. Engineers, repair technicians, and manufacturers will find that the CircuitWorks® Conductive Pen speeds project completion and cuts rework time.
?? Single component system
?? High electrical conductivity
?? Fast drying
?? Highly adherent to circuit boards
?? Operating temperature to 400°F （205°C）
TYPICAL APPLICATIONS
CircuitWorks® Conductive Pen may be used for electronics applications including:
?? Circuit Trace Repair
?? Solderless Linking of Components
?? EMI Shielding
?? Solderable Terminations
?? Quick Prototype Modifications
CHEMTRONICS®
Technical Data Sheet
CircuitWorks® Conductive Pen
TYPICAL PRODUCT DATA AND PHYSICAL PROPERTIES
Composition
Material Silver Filled Polymer
Silver Particle Size
10-15 microns
Color
Silver Gray
Setting Rate
<2mm/hr.
Properties
Conductivity 0.02-0.05 ohms/sq/mil
0.00005-0.000125 ohm cm
Max. Temperature 400°F （205°C）
Tack-Free Time @ 25°C 3 to 5 Minutes
Cure Time @ 25°C 20 to 30 Minutes
Solder Wetting 2 to 3 Seconds
Electrical Conductivity Excellent
Adhesion Excellent
Flexibility Good
Chemical Resistance Good
Tip Diameters
MTP 0.8 mm （0.03 inches）
STP 1.2 mm （0.05 inches）
Shelflife 12 months
COMPATIBILITY
CircuitWorks® Conductive Pen material has excellent compatibility with materials used in printed circuit board fabrication. As with any chemical system, compatibility with the substrate must be determined on a non-critical area prior to use.
USAGE INSTRUCTIONS
Read MSDS carefully prior to use.
Cleaning: For best adhesion, clean board with one of Chemtronics Electro-Wash® or Pow-R-Wash® solvents in order to remove any surface contamination which may prevent adequate material contact.
Mixing: Although this system has been formulated to resist hard-packing, it should be shaken vigorously for 30 seconds to insure the proper dispersion of the silver flakes. If pen has been allowed to sit idle for a long period of time, the mixing ball may seize in the barrel. To free the ball use force to tap the barrel end of the pen until the ball begins to move inside the pen.
Application: The conductive ink is dispensed through the CircuitWorks® Conductive Pen. Squeezing the pen body while pressing down on the surface will allow the material to flow, enabling the trace to be drawn. Practice with the pen before attempting detail work. The bulk form of this material may be applied by brushing, banding, or automatic dispensing equipment.
Thinning: The conductive ink has been optimized for the CircuitWorks® Conductive Pen and thinning is not normally necessary. However, Butyl Acetate may be added with thorough mixing to make slight adjustments for ease of application in the bulk form.
Clean-up/Removal: The conductive ink may be cleaned or removed using a strong organic solvent such as Chemtronics® Electro-Wash® PX.
Curing: Tack-free in 3 to 5 minutes at room temperature. Achieves electrical conductivity within 30 minutes. Heat cure for 5 minutes at 250 to 300°F （120 to 150°C） for maximum conductivity, durability and chemical resistance.
Soldering: Low temperature soldering is possible to the heat-cured silver conductive traces if done at 350°F （177°C） for <5 seconds.
AVAILABILITY
CW2200STP 8.5 g （0.3 oz.）, Standard 1.2 mm tip
CW2200MTP 8.5g （0.3 oz.）, MicroTip 0.8 mm tip
TECHNICAL & APPLICATION ASSISTANCE
Chemtronics® provides a technical hotline to answer your technical and application related questions. The toll free number is: 1-800-TECH-401.
NOTE:
This information is believed to be accurate. It is intended for professional end users having the skills to evaluate and use the data properly. ITW CHEMTRONICS® does not guarantee the accuracy of the data and assumes no liability in connection with damages incurred while using it.
MANUFACTURED BY:
ITW CHEMTRONICS®
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888 REV. F （06/09）
DISTRIBUTED BY:
上一篇：SW14025 SW14035 SW14045 SW14015 無鉛吸錫線成份報告
下一篇：沒有了
